This is an old revision of the document!
QT Creator is a cross-platform IDE designed to build Qt applications. The Qt Creator IDE is currently the preferred choice to build and run custom qt applications on the reMarkable tablet.
$ sudo apt install qtcreator
Please note: on Linux Mint install Qt Creator by means of the Qt web installer. Via package manager it didn't work, possibly a too old version on the repo?
# pacman -S qtcreator
# yum install qt-creator
For other Linux distributions, please refer to the distribution specific package manager and package list. Optionally, or if your distribution does not provide a qt-creator package, you may follow the official Qt Creator Manual and build Qt Creator from source.
For applications to be able to run on the reMarkable, they must be compiled for the ARM architecture using the toolchain provided by reMarkable engineering.
Download the toolchain installer on your host machine
$ curl https://remarkable.engineering/deploy/sdk/poky-glibc-x86_64-meta-toolchain-qt5-cortexa9hf-neon-toolchain-2.1.3.sh -o install-toolchain.sh
Execute the toolchain installer
$ chmod +x install-toolchain.sh $ ./install-toolchain
You will be prompted to specify an installation path. It is highly recommended to use the default SDK path as it is used trough out this article.
The QT Creator IDE must first be configured to support cross-compiling for the reMarkable tablet. It is assumed that the toolchain has been installed to
Open the options menu under Tools > Options > Build & Run and follow the latter steps
Under the QT Versions tab, click on
Add… and select the qmake binary located in
/opt/poky/2.1.3/sysroots/x86_64-pokysdk-linux/usr/bin/qt5/qmake. Set the Version name to reMarkable 5.6.2 to follow up with this guide.
Under the compilers tab, click
GCC. From there you'll have to add a C and C++ compiler.
Set the path of both compilers to
/opt/poky/2.1.3/sysroots/x86_64-pokysdk-linux/usr/bin/arm-poky-linux-gnueabi/arm-poky-linux-gnueabi-gcc and name them reMarkable GCC each.
Under the debuggers tab, click
Add and set the path to
Set the name to reMarkable GDB
Under the kits tab, click
Add. From there ensure all properties are set as shown in the following table :
|File system name|
|Device Type||Generic Linux Device|
|Compiler (C)||reMarkable GCC|
|Compiler (C++)||reMarkable GCC|
|Environment||No changes to apply.|
|Qt version||reMarkable 5.6.2|
CMake related properties have been left out from the table as they should remain unmodified.
QT has to be able to establish connection to your device for it to directly install and execute code on it.
You must add an entry for your reMarkable tablet under Tools > Options > Devices. From there click Add > Generic Linux Device.
Set a name for the device, such as reMarkable, and specify the necessary SSH credentials to access your device.
After all steps above have been completed, close the current session of Qt Creator and source the toolchain environment.
From the very same terminal you may then open Qt Creator
$ source /opt/poky/2.1.3/environment-setup-cortexa9hf-neon-poky-linux-gnueabi $ qtcreator
On every new shell session, the toolchain environment must be sourced before Qt Creator has been opened.*
At this point, Qt Creator should be able to build and execute code on your reMarkable tablet as long as its unlocked and connected (via SSH) to the host machine.
The device's graphical interface, xochitl, may undesirably interfere and overlap with the executed Qt Application. To stop this behavior from reoccurring, stop the xochitl service on your reMarkable trough systemctl
remarkable: ~/ systemctl stop xochitl
To start the GUI again, either restart the device or start xochitl from systemctl
remarkable: ~/ systemctl start xochitl